Help ENES

Electric & Pneumatic Jackhammer Rentals in Irvine, CA

24 jackhammers available Nov 12 – Nov 15 Change
Jackhammers Irvine, CA · 25 mi Nov 12 – 15 · 3 days Edit search

Showing 8 of 24

No jackhammers match those filters

Widen the price range or clear the weight class — 17 other breakers are available in Irvine this week.

06 Before you book

Jackhammer selection guide & platform rules

Match the breaker to the concrete, check what the power drop can carry, and know the deposit terms before the truck leaves the yard.

Technical specs & sizing

Weight class decides the job. Anything heavier than the slab needs is money burned on freight.

Class Tool weight Best for Power draw Shank
Light chippingUnder 30 lb 15–30 lb Mortar, tile, thin topping, overhead and wall work 10–15 A
30–40 CFM
SDS-Max
3/4 in hex
Medium demolition30–45 lb 30–45 lb Footings, trenching, 4–6 in slab, utility cuts 15 A dedicated
55–70 CFM
SDS-Max
1 in hex
Heavy breaker55–70 lb 55–70 lb Driveways, sidewalks, 6–8 in concrete without rebar 15–20 A
85–100 CFM
1-1/8 in hex
Pavement breaker75–95 lb 75–95 lb Roadway, bridge deck, reinforced concrete, bushing work Pneumatic
100–120 CFM
1-1/8 in × 6 in

Rule of thumb: a 30-lb hammer removes roughly 1 in of slab per pass. Going one class up cuts the work in half and doubles the freight weight.

Power requirements

Pneumatic Needs air

  • Breaker CFM must sit at or below compressor output at 90 psi.
  • Add 20–30% for runs over 50 ft of hose.
  • Use 3/4 in hose; 1/2 in chokes a 90-lb breaker.

Electric 110–120V

  • 15–20 A tools need a dedicated 20 A circuit.
  • 12-gauge cord, 50 ft max — longer runs trip breakers.
  • On a generator, size 1.5× the running amps.

Rental rules & policy

01How is the security deposit handled?

A hold of $150 or one day’s rate — whichever is higher — is authorized on your card through Stripe. Nothing is charged at booking. The hold releases 24–48 hours after the owner’s return inspection clears.

02What is the fuel and cleaning policy?

Return the tool free of cured concrete and, for gas units, with a full tank. Otherwise a refuel fee of $25 plus fuel or a cleaning fee of $45/hour applies, itemized on the closing invoice. Electric and pneumatic breakers carry no fuel charge.

03What happens if the breaker fails on the jobsite?

Damage waiver at 12% of the rental covers incidental damage and normal wear. If a unit fails mechanically through no fault of the crew, the owner or the platform swaps it same day inside the delivery radius, and the lost hours are credited.

04Do I need insurance to book?

Yes for business accounts: a certificate of insurance showing $1M general liability naming the equipment owner as additional insured. Sole operators can buy a per-rental policy at checkout.

05How precise are delivery windows?

Two-hour windows, GPS-tracked to the jobsite gate. You get a live ETA refreshed every 30 seconds and a driver call at the 20-minute mark.

06Can I cancel or extend?

Free cancellation until 24 hours before pickup; after that one day’s rate applies. Extensions are approved in the dashboard while the unit is still on rent, subject to the next booking.

07Do you invoice on Net-30?

Verified businesses with a W-9 on file get Net-30 terms. Closing documents — invoice, waiver, inspection record — issue automatically to your billing email and sync to Gigo CRM.

What ships in the case

Moil point Flat chisel Retaining pin Chuck Owner manual

Included at no extra cost on every verified listing

Asphalt cutters, clay spades and bushing tools rent separately — filter by chisel type on the card list.

Safety & PPE check

  • Safety glassesZ87.1 rated, worn under the shield
  • Hearing protectionNRR 25+ — these tools run 100–115 dB
  • Anti-vibration glovesCut the hand-arm vibration dose
  • Steel-toe boots and a dust mask for indoor pours

Breaking concrete releases respirable silica. OSHA requires water or vacuum dust control on handheld breakers under 29 CFR 1926.1153 Table 1. Wet-cutting attachments rent with the tool.